Uvex Profabutyl B-05R Safety Gloves

Standards and labels

• EN ISO 374-1:2016

  EN ISO 374-1:2016 is a standard that defines the performance requirements for gloves that protect against chemicals and microorganisms. The standard specifies the design, materials, and testing requirements for gloves to protect against chemicals and microorganisms. Possible test results include measurements of the gloves' permeation resistance, degradation, and penetration. It also includes the safety and functionality requirements for gloves.

  Test results

  Specified Requirements Type A

• EN 388:2016

  EN 388:2016 is a European standard for measuring the performance of protective gloves against mechanical risks (abrasion, cut, tear, and puncture). The standard includes test methods and performance requirements for gloves to be considered compliant. Test results are reported using a series of four numbers, each representing the performance level achieved in one of the tests.

  Test results

  Tear Resistance Level 1

  EN 388:2016 is a European standard that outlines the testing requirements for gloves to determine their level of protection against mechanical hazards, including tear resistance. The Tear Resistance Level 1 classification signifies that the gloves offer basic protection against tearing. The test method involves applying a force to a sample of the glove material to tear it, and the force measured reflects the glove's ability to resist tearing. Level 1 tear resistance means the gloves can withstand a force of between 10 to 25 Newtons before tearing. This basic level of protection is suitable for tasks where there is a minimal risk of tearing due to light manual handling or where gloves are used to prevent scratches or minor abrasions. Gloves with Level 1 tear resistance are appropriate for general activities that do not involve handling sharp or jagged materials.

  Puncture Resistance Level 0

  EN 388:2016 specifies safety glove standards, including puncture resistance. The test result Level 0 in puncture resistance indicates that the product does not meet the minimal requirements set by the standard for protecting against punctures. The test method used involves using a standardized stylus with a specified force applied to the glove material. This is measured by the amount of force needed before the stylus punctures through the glove material. A Level 0 result signifies that the glove failed to provide any standardized level of protection during the testing procedure, which means it is not suitable for environments where puncture resistance is required for safety purposes .

  Cut Resistance, ISO 13997 Level X

  The standard EN 388:2016, specifically its segment referring to ISO 13997 test, is designed to assess the cut resistance of materials used in protective gloves. A result denoted as 'Level X' means that test is not performed and the cut resistance of the product cannot be guaranteed.

  Cut Resistance, Coup Test Level 0

  The EN 388:2016 standard specifies requirements and test methods for protective gloves in relation to physical and mechanical aggressions due to abrasion, blade cut, tear, puncture, and impact resistance. A Cut Resistance Level 0 result in this standard implies that the protective gloves under assessment offer very minimal to no protection against cutting hazards. The Coup Test, utilized to determine this result, involves rotating a circular blade under constant pressure against the glove material until it is cut through. This test specifically assesses how well glove materials can withstand cutting forces from a sharp, circular blade. For procurement professionals, this result indicates that gloves with a Cut Resistance Level 0 are unsuitable for environments where there is a risk of hand injuries from sharp objects as they provide the lowest level of cut resistance under EN 388:2016.

  Abrasion Resistance Level 2

  EN 388:2016 is an updated European standard that specifies criteria for testing gloves to protect against mechanical risks, including abrasion, cuts, tears, and puncture. The Abrasion Resistance Level 2 classification within this standard indicates a moderate level of protection against wear from rough materials. The abrasion resistance test involves subjecting the glove material to repeated cycles of sandpaper under pressure until the material wears through. Level 2 abrasion resistance means the gloves can withstand between 500 to 1999 cycles before being penetrated. This level of protection is suitable for tasks that involve handling or coming into contact with abrasive materials but not at an extreme or heavy-duty level. Gloves with Level 2 abrasion resistance are well-suited for general handling tasks, offering durability and protection to extend the life of the glove while maintaining good dexterity and comfort.

• EN 16350:2014

  EN 16350:2014 is a European standard that defines the performance requirements for windows and doors in buildings. It covers testing procedures for measuring the safety and security aspects of these products. Test results should show compliance with the standard's requirements, including the resistance to forced entry, load resistance and the ability to open and close easily.

  Test results

  Electrostatic Properties Tested

  EN 16350:2014 specifies the test methods and requirements for the electrostatic properties of protective clothing used to avoid incendiary discharges, particularly in environments where there is a risk of explosion. The 'Tested' designation indicates that the material has undergone evaluation to ensure it dissipates electrostatic charges effectively under specific conditions. The standard testing method involves measuring the electrical resistance of the fabric under controlled humidity and temperature conditions to ensure that the material can safely conduct electrical charges away from the body. Protective clothing meeting this standard is essential in industries like petrochemicals, electronics manufacturing, and pharmaceuticals, where static electricity can pose a significant risk of sparking explosions or fires. This certification assures that the clothing provides a necessary level of protection against electrostatic discharge, contributing to the safety and prevention of accidents in hazardous work environments.

• EN ISO 21420:2020

  Test results

  General Requirements Guide

  EN ISO 21420:2020 is a standard that outlines general requirements and guidelines for protective gloves, aiming to ensure their quality, performance, and suitability for various applications. When a product meets the requirements outlined in the General Requirements section of EN ISO 21420:2020, it signifies that the gloves comply with fundamental quality and performance criteria, including factors such as size, fit, ergonomics, and dexterity. The practical implications of this compliance are significant, as it assures users of the gloves' basic functionality and suitability for general hand protection purposes across a range of industries and applications. The test method involves evaluating various aspects of the gloves, including dimensions, construction, materials, and labeling, to ensure conformity with the specified requirements. Compliance with these general requirements enhances user confidence in the protective gloves' reliability and effectiveness, promoting workplace safety and facilitating compliance with regulatory standards.

• CE Marking

  CE Marking is a label that shows a product meets certain safety and environmental standards set by the European Union. To get the CE Marking, a company must test and certify their product meets these standards. CE Marking is required for many products sold in the EU, including electronics, machinery, toys and medical devices. It helps ensure that products are safe for consumers and the environment, and allows for easy trade within the EU.