Standards and labels

• EN ISO 21420:2020

  EN ISO 21420:2020 is a European standard that sets out the general requirements for hand protection, including comfort, fit, and dexterity.

  Reach out to ask about the standard test results

• EN 388:2016

  EN 388:2016 is a European standard for measuring the performance of protective gloves against mechanical risks (abrasion, cut, tear, and puncture). The standard includes test methods and performance requirements for gloves to be considered compliant. Test results are reported using a series of four numbers, each representing the performance level achieved in one of the tests.

  Test results

  Puncture Resistance Level 1

  The European standard EN 388:2016 addresses the puncture resistance of protective gloves, with puncture resistance classified from Levels 1 to 4. Specifically, a Level 1 result indicates minimal puncture resistance. This level of resistance is determined by a test involving a standardized stylus with a specified diameter and force. During the test, the stylus is pressed against the material with a force up to 20 Newtons to assess how well the glove can withstand penetration. A Level 1 rating signifies that the glove provides basic protection against small punctures or stabs, appropriate for areas with minimal risk. Practical implications for this test result suggest the gloves are suitable for light tasks where major risks of punctures are not anticipated, but are not adequate for handling sharp tools or heavy equipment where higher penetration resistance would be necessary.

  Tear Resistance Level 3

  EN 388:2016 is a European standard that specifies methods for testing the resistance of protective gloves against mechanical hazards, such as abrasion, cuts, punctures, and tearing. The Tear Resistance Level 3 indicates a high level of protection, where the gloves can withstand significant tearing forces. The test for determining tear resistance involves subjecting the glove material to a mechanical force until it tears, measuring the force required to initiate and continue the tear. For Level 3, gloves must withstand a force between 50 to 75 Newtons before tearing. This robust level of tear resistance is particularly suitable for demanding environments where gloves are exposed to activities that might cause extensive wear or tearing, such as handling heavy or rough materials, industrial assembly, and construction tasks. Gloves with this level of tear resistance provide enhanced durability and safety, reducing the risk of injuries and increasing the longevity of the glove in tough working conditions.

  Cut Resistance, Coup Test Level 1

  The EN 388:2016 standard is dedicated to gauging the mechanical risks for hand protection where a Cut Resistance, Coup Test Level 1 indicates minimal resistance to cutting because material achieved between 1.2 and 2.5 cycles before being cut through during the test. It means that the product tested at this level offers basic protection against shallow cuts, suitable for tasks with low risk of cut injuries. The test method used involves a rotating circular blade under a fixed force making contact with the fabric or material being tested. The blade moves back and forth across the material until a cut-through is achieved. The number of cycles required to cut through the sample at a consistent speed determines the cut resistance, with Level 1 being the second lowest rating after level 0. Products at this level are applicable in scenarios where there are minimal hazards from sharp objects, hence ideal for light duties where there is no significant risk of deep cuts.

  Cut Resistance, ISO 13997 Level A

  The cut resistance result of Level A based on ISO 13997 in the standard EN 388:2016 indicates a force of greater than 2 Newtons required to cut through the material. This is considered the first level on a scale that ranges up to Level F, where each level corresponds to higher thresholds of force needed to penetrate the material, with Level F exceeding 30 Newtons. The testing method employs a TDM test device equipped with a single-use straight edge blade. During the test, the blade is drawn only once across the material in one direction, and once the blade cuts through the sample, the distance the blade has traveled is recorded. This standardized testing ensures that the cut resistance of materials like gloves can be measured more accurately, especially those fabricated from high-cut resistance materials that might blunt a blade. The practical implication of obtaining a result of Level A in this test is that the material provides basic cut protection and is suitable for tasks with minimal cut hazards, such as light material handling or small parts assembly.

  Abrasion Resistance Level 4

  EN 388:2016 uses a specific test method to measure abrasion resistance of safety gloves; the gloves’ material is subjected to sandpaper under pressure to observe the number of cycles needed to wear through the material. Level 4 in this standard indicates that the material withstood 8,000 cycles before a hole was made. Practically, this means that gloves rated at Level 4 for abrasion resistance offer very high resilience against wearing through, making them suitable for tasks involving significant contact with rough surfaces .

• EN 407:2004

  EN 407:2004 is a European standard that specifies the safety requirements for protective gloves for thermal risks. It sets rules for the design, construction, and testing of gloves that protect users from heat and fire. Testing includes measurements of contact heat, convective heat, radiant heat, small splashes of molten metal and flame resistance. The standard also includes requirements for labeling and instructions for use. This standard is an updated version of EN 407:1994 and it's intended to protect the users against thermal risks, such as heat and flame, and to help them to choose a suitable glove for their specific application.

  Test results

  Molten Metal Resistance Level X

  EN 407:2004 is a European standard that provides specifications for protective gloves to safeguard against thermal risks, including the exposure to molten metals. The designation Molten Metal Resistance Level X indicates that the gloves have not been tested for this specific risk, or they failed to meet the minimum requirements set out in the standard for protection against molten metal splashes. This means that the gloves are either unsuitable for use in environments where there is a risk of contact with molten metals, or additional testing is required to determine their suitability. Typically, such a classification implies that the gloves should not be used for handling molten metals and should only be considered for other types of thermal risks specified in the standard, where molten metal exposure is not a concern. This classification helps in ensuring that users select the right type of glove based on the specific hazards present in their working environment, thereby preventing inappropriate use and enhancing safety.

  Burning Behaviour Level X

  The EN 407:2004 standard addresses the burning behavior of gloves protecting from heat and/or fire. A performance level X in this context indicates that the glove has not been submitted for testing under the specified part of the standard or failed the test.

  Heat Contact Level 1

  The standard EN 407:2004 on Protective gloves against thermal risks, including the testing for contact heat at Level 1, is designed to assess the protection level of gloves when exposed to thermal hazards. A Level 1 result on the contact heat resistance indicates basic protection where the glove can delay the transfer of heat from a contact source at 100°C for at least 15 seconds before the inside of the glove reaches a temperature increase of 10°C. The test method involves placing the outer surface of the glove in contact with a hot probe of defined dimensions and temperature, while the rate of temperature rise of a calorimeter on the inside of the glove is measured. This measurement provides a straightforward metric for assessing the thermal protection offered by the glove at low-level exposure. Practically, gloves rated at Level 1 for contact heat are suitable for environments where exposure to thermal risks is minimal and not excessively severe, making them adequate for certain low-risk industrial, laboratory, or handling applications where brief contact with warm objects is common.

  Heat Convection Level X

  The EN 407:2004 European standard and its annexure for Heat Convection Level X is designed to gauge the protective capability of gloves when exposed to heat transmitted through a fluid medium, such as air or steam. The designation of Level X specifically indicates that the material did not meet the minimum requirements set forth in the test, or wasn't tested due to being deemed unsuitable for this type of exposure based on the nature of the material. The test method for determining this involves measuring the time it takes for the material to increase in temperature by 24°C under standardized conditions of convection heat exposure. This test is important for defining the efficacy of protective gear under various industrial conditions where heat convection is a risk.

  Radiant Heat Level X

  EN 407:2004 is a European standard that sets the requirements for protective gloves to defend against various thermal hazards, including radiant heat. The designation Radiant Heat Level X indicates that the gloves have not been tested for this specific type of protection, or they did not meet the minimum criteria established by the standard for resisting radiant heat. This means that these gloves are not certified for protection against radiant heat, which involves the transmission of heat through infrared rays from a heat source without direct contact. The lack of a specific radiant heat protection level suggests that users should not rely on these gloves for tasks where significant exposure to radiant heat is expected. Instead, these gloves might be suitable for other types of thermal risks for which they are certified, ensuring users select the appropriate type of protective glove based on the specific hazards present in their working environment. This classification assists in preventing inappropriate glove use and enhancing worker safety by clearly indicating the limitations of the glove's protective capabilities.

  Metal Splash Resistance Level X

  The EN 407:2004 standard specifies different levels of protection for gloves against thermal risks, including metal splash resistance. A result marked as 'Level X' under this standard symbolizes that the glove material either did not meet the minimum requirements for testing or that no specific test was conducted for this hazard. The test for Metal Splash Resistance in EN 407:2004 involves exposing the glove material to molten metal splashes to determine how much molten metal is required to heat the glove material to a degree that it would cause pain or injury to the wearer. The practical implication of a 'Level X' rating is that gloves marked as such should not be relied upon for protection against risks of molten metal splashes, making them unsuitable for use in environments where exposure to this hazard is likely.

• Ecovadis

  Ecovadis rating and certification system is used in Europe to evaluate and recognize companies' sustainability performance. It is focused on the supply chain and evaluates companies on environmental, social and ethical criteria, such as environmental protection, labor practices, and fair business practices. The requirements for getting an Ecovadis certification will depend on the specific category of business and industry, but typically include providing information on the company's sustainability practices, policies and performance, and undergoing an assessment by an independent auditor.

• CE Marking

  CE Marking is a label that shows a product meets certain safety and environmental standards set by the European Union. To get the CE Marking, a company must test and certify their product meets these standards. CE Marking is required for many products sold in the EU, including electronics, machinery, toys and medical devices. It helps ensure that products are safe for consumers and the environment, and allows for easy trade within the EU.

• Dermatologically Tested

  Dermatologically Tested refers to products that have been tested and proven to be safe for use on the skin. The European Union has regulations for cosmetics products, which includes dermatological testing, to ensure that products are safe for use. To be labeled as dermatologically tested, the product must be tested by a qualified professional, such as a dermatologist, and must not cause any irritation or allergic reactions. The testing must be carried out on a representative sample of human volunteers and the results must be evaluated by a qualified professional before the product can be considered as dermatologically tested and can bear the label. The EU Cosmetics Regulation, lays out the specific requirements for safety assessments and labeling of cosmetics products.

• Food Safe

  Food safe refers to the safety of food products that are used or consumed by people. In Europe, food safety is regulated by the European Union (EU) and the European Food Safety Authority (EFSA). These organizations set standards and requirements for food products to ensure they are safe to eat. To be considered "food safe" in Europe, a product must meet these standards and be free of harmful substances. This includes being free of harmful bacteria, pesticides, and other contaminants. Food products that do not meet these standards cannot be sold or used in the EU.

• PPE Category 3

  PPE stands for "personal protective equipment." PPE Category 3 refers to equipment that is complex and provide the highest level of protection such as powered respirators, SCBA, and full body suits. In Europe, PPE Category 3 must meet certain safety standards set by the European Union, which means that it must be designed and manufactured to protect the user without causing harm. Companies that make or sell PPE must prove that it meets these standards. They also must have a quality management system in place, have to be audited regularly by a notified body and have to have a technical documentation.

• Oeko-Tex Standard 100

  Oeko-Tex Standard 100 is a product certification program for textiles, which is awarded by the Oeko-Tex Association. This program verifies that the textile products are free from harmful chemicals. To be able to use the Oeko-Tex Standard 100 label, a product must meet certain requirements set by the Oeko-Tex Association which include limits on the levels of harmful substances such as pesticides, heavy metals, and formaldehyde. The textile products are inspected and certified by Oeko-Tex, they can use the Oeko-Tex Standard 100 label on their packaging to show that they are free from harmful chemicals. This certification is for all types of textiles, from raw materials to finished products, and it is globally recognized.