Standards and labels

• EN 407:2004

  EN 407:2004 is a European standard that specifies the safety requirements for protective gloves for thermal risks. It sets rules for the design, construction, and testing of gloves that protect users from heat and fire. Testing includes measurements of contact heat, convective heat, radiant heat, small splashes of molten metal and flame resistance. The standard also includes requirements for labeling and instructions for use. This standard is an updated version of EN 407:1994 and it's intended to protect the users against thermal risks, such as heat and flame, and to help them to choose a suitable glove for their specific application.

  Test results

  Heat Contact Level 1

  The standard EN 407:2004 on Protective gloves against thermal risks, including the testing for contact heat at Level 1, is designed to assess the protection level of gloves when exposed to thermal hazards. A Level 1 result on the contact heat resistance indicates basic protection where the glove can delay the transfer of heat from a contact source at 100°C for at least 15 seconds before the inside of the glove reaches a temperature increase of 10°C. The test method involves placing the outer surface of the glove in contact with a hot probe of defined dimensions and temperature, while the rate of temperature rise of a calorimeter on the inside of the glove is measured. This measurement provides a straightforward metric for assessing the thermal protection offered by the glove at low-level exposure. Practically, gloves rated at Level 1 for contact heat are suitable for environments where exposure to thermal risks is minimal and not excessively severe, making them adequate for certain low-risk industrial, laboratory, or handling applications where brief contact with warm objects is common.

  Burning Behaviour Level X

  The EN 407:2004 standard addresses the burning behavior of gloves protecting from heat and/or fire. A performance level X in this context indicates that the glove has not been submitted for testing under the specified part of the standard or failed the test.

  Molten Metal Resistance Level X

  EN 407:2004 is a European standard that provides specifications for protective gloves to safeguard against thermal risks, including the exposure to molten metals. The designation Molten Metal Resistance Level X indicates that the gloves have not been tested for this specific risk, or they failed to meet the minimum requirements set out in the standard for protection against molten metal splashes. This means that the gloves are either unsuitable for use in environments where there is a risk of contact with molten metals, or additional testing is required to determine their suitability. Typically, such a classification implies that the gloves should not be used for handling molten metals and should only be considered for other types of thermal risks specified in the standard, where molten metal exposure is not a concern. This classification helps in ensuring that users select the right type of glove based on the specific hazards present in their working environment, thereby preventing inappropriate use and enhancing safety.

  Metal Splash Resistance Level X

  The EN 407:2004 standard specifies different levels of protection for gloves against thermal risks, including metal splash resistance. A result marked as 'Level X' under this standard symbolizes that the glove material either did not meet the minimum requirements for testing or that no specific test was conducted for this hazard. The test for Metal Splash Resistance in EN 407:2004 involves exposing the glove material to molten metal splashes to determine how much molten metal is required to heat the glove material to a degree that it would cause pain or injury to the wearer. The practical implication of a 'Level X' rating is that gloves marked as such should not be relied upon for protection against risks of molten metal splashes, making them unsuitable for use in environments where exposure to this hazard is likely.

  Radiant Heat Level X

  EN 407:2004 is a European standard that sets the requirements for protective gloves to defend against various thermal hazards, including radiant heat. The designation Radiant Heat Level X indicates that the gloves have not been tested for this specific type of protection, or they did not meet the minimum criteria established by the standard for resisting radiant heat. This means that these gloves are not certified for protection against radiant heat, which involves the transmission of heat through infrared rays from a heat source without direct contact. The lack of a specific radiant heat protection level suggests that users should not rely on these gloves for tasks where significant exposure to radiant heat is expected. Instead, these gloves might be suitable for other types of thermal risks for which they are certified, ensuring users select the appropriate type of protective glove based on the specific hazards present in their working environment. This classification assists in preventing inappropriate glove use and enhancing worker safety by clearly indicating the limitations of the glove's protective capabilities.

  Heat Convection Level X

  The EN 407:2004 European standard and its annexure for Heat Convection Level X is designed to gauge the protective capability of gloves when exposed to heat transmitted through a fluid medium, such as air or steam. The designation of Level X specifically indicates that the material did not meet the minimum requirements set forth in the test, or wasn't tested due to being deemed unsuitable for this type of exposure based on the nature of the material. The test method for determining this involves measuring the time it takes for the material to increase in temperature by 24°C under standardized conditions of convection heat exposure. This test is important for defining the efficacy of protective gear under various industrial conditions where heat convection is a risk.

• EN 388:2016

  EN 388:2016 is a European standard for measuring the performance of protective gloves against mechanical risks (abrasion, cut, tear, and puncture). The standard includes test methods and performance requirements for gloves to be considered compliant. Test results are reported using a series of four numbers, each representing the performance level achieved in one of the tests.

  Test results

  Abrasion Resistance Level 4

  EN 388:2016 uses a specific test method to measure abrasion resistance of safety gloves; the gloves’ material is subjected to sandpaper under pressure to observe the number of cycles needed to wear through the material. Level 4 in this standard indicates that the material withstood 8,000 cycles before a hole was made. Practically, this means that gloves rated at Level 4 for abrasion resistance offer very high resilience against wearing through, making them suitable for tasks involving significant contact with rough surfaces .

  Cut Resistance, ISO 13997 Level C

  The EN 388:2016 standard comprehensively addresses the cut resistance of gloves, using the ISO 13997 test method, where achieving Level C indicates that the glove can withstand forces between 10 to 14 newtons during cutting. This level of cut resistance provides an intermediate level of protection against cuts, suitable for handling tasks where there is a significant risk of cuts from sharp objects but where the highest level of cut resistance isn't necessary. The ISO 13997 test itself is a more detailed and clear manner to assess material cut resistance under a straight-edge blade under varying load, unlike the Coup Test used previously, which could blunt the blade. Essentially, Level C gloves are designed for robust hand protection in environments where cut hazards are considerable but not at the most extreme end of the scale, making them suitable for industries like construction and manufacturing where sharp tools and materials are frequently handled.

  Cut Resistance, ISO 13997 Level X

  The standard EN 388:2016, specifically its segment referring to ISO 13997 test, is designed to assess the cut resistance of materials used in protective gloves. A result denoted as 'Level X' means that test is not performed and the cut resistance of the product cannot be guaranteed.

  Puncture Resistance Level 2

  The standard EN 388:2016 includes an assessment of Puncture Resistance, where Level 2 signifies that the material has met specific criteria for resistance against puncture. The result of Level 2 in puncture resistance means that the protective glove or material can withstand a force of 60 to 100 newtons before being punctured. The test method used involves using a standardized steel puncture probe that is pushed against the material at a specified speed until it pierces through it. In essence, achieving a Level 2 puncture resistance under EN 388:2006 suggests that the protective equipment offers moderate protection against punctures, making it suitable for environments where there is a risk of encountering sharp objects such as needles, but are not excessively sharp or exert very high force.

  Tear Resistance Level 4

  EN 388:2016 is a European standard that establishes criteria for assessing the protection provided by gloves against mechanical hazards, including tear resistance. The Tear Resistance Level 4 classification represents the highest level of tear resistance defined by this standard, indicating that the gloves can withstand the most substantial forces before tearing. According to the testing methodology, gloves are evaluated by measuring the force required to tear a sample of the glove material, with Level 4 requiring a force of over 75 Newtons to initiate and propagate a tear. This high level of tear resistance is ideal for use in environments where gloves are subjected to significant stress and potential damage, such as in heavy industry, construction, and handling of materials with sharp edges. Gloves achieving this level offer superior durability and are essential for ensuring user safety in high-risk mechanical settings, thereby enhancing work efficiency and reducing the frequency of glove replacement.

• CE Marking

  CE Marking is a label that shows a product meets certain safety and environmental standards set by the European Union. To get the CE Marking, a company must test and certify their product meets these standards. CE Marking is required for many products sold in the EU, including electronics, machinery, toys and medical devices. It helps ensure that products are safe for consumers and the environment, and allows for easy trade within the EU.

• PPE Category 2

  PPE stands for "personal protective equipment." PPE Category 2 refers to equipment that is more complex, and has a higher level of risk. Examples of PPE Category 2 include safety helmets, ear protection, and fall arrest equipment. In Europe, PPE Category 2 must meet certain safety standards set by the European Union, which means that it must be designed and manufactured to protect the user without causing harm. Companies that make or sell PPE must prove that it meets these standards. They also must have a quality management system in place and have to be audited regularly by a notified body.